TeamSwift
http://www.teamswift.net/

Underdrive pullies - [3 Tech] - currently out of stock
http://www.teamswift.net/viewtopic.php?f=17&t=16180
Page 6 of 7

Author:  nixmixin [ Fri Mar 16, 2012 7:47 pm ]
Post subject:  Re: Underdrive pullies for 1.0/1.3 SOHC - [3 Tech]

I may be missing something but, do any of these have the 2 belt for AC? In Vegas, AC is a must. I cant tell from the pic and tried to find in this thread something about the 2 belt pully.

thanks

Author:  suprf1y [ Fri Mar 16, 2012 8:38 pm ]
Post subject:  Re: Underdrive pullies for 1.0/1.3 SOHC - [3 Tech]-OUT OF ST

suprf1y wrote:
OK ladies, I'm looking at doing a run of pulleys and hopefully get enough interest to be able to sell them for $50 each plus shipping. I'll have to weigh them to be sure, but I expect shipping to be about $8, and definitely no more than $10. If it is, I'll cover the difference. Remember I'm shipping small packet air from Canada.

They will be 4"/100 mm diameter (25% under drive) , 4 groove (will also work on 3 groove cars) single pulley with 4 or 5 bolt holes as required.
I don't have a price for the anodizing yet, but don't expect it to change the pricing. If it does, they will either be available in plain aluminum, or anodized at the higher price, depending on what you guys want. If anodized, there will only be one colour, and I haven't determined what it will be yet.
Order qty will determine final price, but I hope to get enough interest to justify a run of 50-100 pulleys, and keep it at $50.

Author:  suprf1y [ Fri Mar 16, 2012 9:08 pm ]
Post subject:  Re: Underdrive pullies for 1.0/1.3 SOHC - [3 Tech]

I found a small mistake on the pulleys, so they're going back for a minor alteration. The keyway is not quite deep enough. It will be re-cut, so the finish will be slightly different than the rest of the pulley.
I should be ready to ship by mid-next week.
Cost will be $50 + $10 shipping for one, $15 for two in N. America. Outside N. America, please contact me beforehand for a shipping quote.

Paypal is fine to 3tech@teamswift.net Payment is in CANADIAN DOLLARS.
There is a tab in the payment section where you can choose the currency you choose to pay with. PP will do the conversion for you.

If PP doesn't work for you, contact me for alternate arrangements.

Information I need with your payment is as follows.
Year of car.
Motor in car.
Number of bolts.
How many pulleys you want.

The address in your account is the only address I will ship to.
If there is no address with your account, include it and your name, with the note.
I will not be able to accept any separate information via PM or email.


Image

Image

Author:  91droptopgeo [ Fri Mar 16, 2012 9:19 pm ]
Post subject:  Re: Underdrive pullies for 1.0/1.3 SOHC - [3 Tech]

Those fargginnn iceholess...They do look pretty sexy.

Chris

Author:  crnolic [ Fri Mar 16, 2012 9:33 pm ]
Post subject:  Re: Underdrive pullies for 1.0/1.3 SOHC - [3 Tech]

Mike let me know when I can pick mine up :D

Author:  suprf1y [ Fri Mar 16, 2012 10:16 pm ]
Post subject:  Re: Underdrive pullies for 1.0/1.3 SOHC - [3 Tech]

91droptopgeo wrote:
Those fargginnn iceholess..


Lousy coarksoakers :lol:

They should be ready to go about mid next week.
First come first served.
I only have 5 (of 51) set aside for myself and 2 buddies.

Author:  91droptopgeo [ Sat Mar 17, 2012 12:24 am ]
Post subject:  Re: Underdrive pullies for 1.0/1.3 SOHC - [3 Tech]

Paypal sent :D

Chris

Author:  EngineWhisperer [ Sat Mar 17, 2012 10:51 am ]
Post subject:  Re: Underdrive pullies for 1.0/1.3 SOHC - [3 Tech]

Paypal Sent. cant wait for the eye candy. 8)

Author:  toolcrib [ Mon Mar 19, 2012 8:39 am ]
Post subject:  Re: Underdrive pullies for 1.0/1.3 SOHC - [3 Tech]

Paypal was sent for two, although I forgot to tag the purchase with my screen name.

My address and cars specified should give it away though.

Thanks,
Andrew

Author:  iamgr8er [ Sat Mar 24, 2012 12:40 pm ]
Post subject:  Re: Underdrive pullies for 1.0/1.3 SOHC - [3 Tech]

Am i going to save gas with these?

Author:  suprf1y [ Mon Mar 26, 2012 4:48 pm ]
Post subject:  Re: Underdrive pullies - [3 Tech] - now in stock

Just an update.

Quote:
I found a small mistake on the pulleys, so they're going back for a minor alteration. The keyway is not quite deep enough. It will be re-cut, so the finish will be slightly different than the rest of the pulley. I should be ready to ship by mid-next week.


I didn't end up getting them until late Thursday, and had to work all weekend. It was my plan to get them all out today, but I woke up at 5 AM sicker than a dog. I was able to get out to the shop just before supper and figure out the jigs, and drilling sequence for the different patterns. I will try to finish them up tonight, and ship tomorrow.

Image

If you paid via paypal and are wondering if I got it, check your own account. It will include the address of where the payment went. I did receive one payment without an address from Chris M.

Author:  EngineWhisperer [ Mon Apr 02, 2012 11:04 pm ]
Post subject:  Re: Underdrive pullies - [3 Tech] - now in stock

Could you post a pic of the jig u used to drill up to 200 :drunk: holes?

Author:  91droptopgeo [ Thu Apr 05, 2012 10:50 pm ]
Post subject:  Re: Underdrive pullies - [3 Tech] - now in stock

Got my pulley today :D. Looks amazing, will test fit tomorrow.

Thanks Suprf1y

Author:  EngineWhisperer [ Fri Apr 06, 2012 9:14 pm ]
Post subject:  Re: Underdrive pullies - [3 Tech] - now in stock

got ,mine a day or two ago and have found a problem. It is way too pretty i put it on and the rest of the motor looks like dog poop. now i have to strip it down and powder coat the rest of the removable parts :D

Author:  suprf1y [ Sat Apr 07, 2012 2:06 am ]
Post subject:  Re: Underdrive pullies - [3 Tech] - now in stock

Let's hope they work as good as they look :lol:

FYI, I've shipped a bunch to Australia already and the cost isn't bad
$21 for one and $38 for two via air shipment.

Author:  crnolic [ Sat Apr 07, 2012 9:50 am ]
Post subject:  Re: Underdrive pullies - [3 Tech] - now in stock

Mike, when are you home? gotta come pick mine up.

Author:  t3 ragtop [ Sat Apr 07, 2012 5:33 pm ]
Post subject:  Re: Underdrive pullies - [3 Tech] - now in stock

here's what i do with them. =)
Image

Image

Author:  Xenth [ Wed Apr 11, 2012 8:44 pm ]
Post subject:  Re: Underdrive pullies - [3 Tech] - now in stock

Sent. :)

Author:  geopat [ Fri Apr 13, 2012 5:35 pm ]
Post subject:  Re: Underdrive pullies - [3 Tech] - now in stock

sending you a pm right now

Author:  blueturbofly [ Sat Apr 14, 2012 12:03 am ]
Post subject:  Re: Underdrive pullies - [3 Tech] - now in stock

8) payment sent for 2 on april 6th 8) gives me a good reason to change my t-belt while its off... =) thanks mike!

Author:  blueturbofly [ Wed Apr 18, 2012 9:07 pm ]
Post subject:  Re: Underdrive pullies - [3 Tech] - now in stock

YAY!!!!!parts arrived today!they look great,nice finish,awesome machine work 8) thanks again,mike!

double bonus when i got home more parts arrived for my other suzuki----engine case for the LTF 250 quadrunner i've been tinkering on----but thats another story

THANKS AGAIN,MIKE!!!!!! :)

Author:  suprf1y [ Tue Apr 24, 2012 11:03 pm ]
Post subject:  Re: Underdrive pullies - [3 Tech] - now in stock

FYI, I'm down to a handful of pulleys.

Just a reminder, I won't ship until I have all your info.

Author:  Xenth [ Wed Apr 25, 2012 1:30 am ]
Post subject:  Re: Underdrive pullies - [3 Tech] - now in stock

suprf1y wrote:
FYI, I'm down to a handful of pulleys.

Just a reminder, I won't ship until I have all your info.

Just confirming that you got all my info, I believe I put everything down correctly, but you never know :P Thanks.

Author:  suprf1y [ Wed Apr 25, 2012 8:11 am ]
Post subject:  Re: Underdrive pullies - [3 Tech] - now in stock

I think it's been shipped, but I am not able to cross reference peoples usernames with their real names and addresses. Send me an email if you would like to know.

Author:  PBC137 [ Wed Apr 25, 2012 10:39 am ]
Post subject:  Re: Underdrive pullies - [3 Tech] - now in stock

Mike, were you able to notch the edge of the outer pulley for a timing light reference? The ones ssgti made, which is what I have, did not seem to be notched.

Page 6 of 7 All times are UTC - 5 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/