TeamSwift
http://www.teamswift.net/

Advanced timing sprockets.
http://www.teamswift.net/viewtopic.php?f=17&t=9066
Page 1 of 3

Author:  suprf1y [ Tue Jul 13, 2004 8:06 am ]
Post subject:  Advanced timing sprockets.

All the results from the test cars have been positive. Because of the amount of PM's, and emails I've been getting, I will now make these available.
The sprockets are intended for the 3cyl. motor with the square tooth timing belt, which I believe to be pre 94. The 94-95 sprockets are also now available, and ocassionally the 96-up sprockets can be had.

They will also work on the 1.3 8V motors, prior to 95, but because of the factory valve timing, I don't recomend any more than +6, and thats only with a fairly healthy cam. If there is interest, I will make +4 sprockets for the 1.3 8V.

This is what is available.
+6, +8, +10 cam sprockets. These are modified stock sprockets.
Dyno testing by B'villetom showed a 5 hp improvement with just a +10 sprocket on a stock motor with open exhaust.

Prices are US$31.50/shipped to US or Canada for the 89-93 sprockets. Shipping is more for the other.

Author:  CaZaM [ Thu Jul 15, 2004 8:48 am ]
Post subject: 

DOHC cam gears? how much?

Author:  suprf1y [ Fri Jul 16, 2004 11:03 am ]
Post subject: 

Wait until I get results from n1tro. If the results are positive, then prices will be the same.

Author:  n1tr0 [ Fri Jul 16, 2004 11:43 am ]
Post subject: 

we're going out to do a bunch of timed runs on some of the different settings this sunday ...

Author:  Bosco [ Fri Aug 13, 2004 8:39 pm ]
Post subject: 

Where?

Author:  n1tr0 [ Fri Aug 13, 2004 10:31 pm ]
Post subject: 

old post ;) sadly, it looks like i'm going to have to wait until i'm over on the mainland next unless someone around here (victoria) has an impact gun ..

Author:  Bosco [ Sat Aug 14, 2004 12:15 pm ]
Post subject: 

To get the stock sprockets off? I knew you hadn't replaced them yet. I have access to an old timing belt if you want to slip that one on and jam a screwdriver in the flywheel ring gear.

Author:  western gti [ Tue Jan 04, 2005 5:33 pm ]
Post subject: 

ANY RESULTS ??

Author:  90sprintSC [ Wed Jan 12, 2005 4:42 am ]
Post subject: 

Is there no core charge? maybe a discount if we send you back our stock sprocket once youres is installed? Eventually you got to run out of sprockets lol.

Author:  suprf1y [ Wed Jan 12, 2005 4:57 am ]
Post subject: 

90sprintSC wrote:
Is there no core charge? maybe a discount if we send you back our stock sprocket once youres is installed? Eventually you got to run out of sprockets lol.


There is no core, but I'll charge you one if that will make you happy :D
The problem is that the core charge would be about what it costs to ship.

Author:  90sprintSC [ Wed Jan 12, 2005 5:15 am ]
Post subject: 

Thanks for clearing that up.

Author:  DTM GTi [ Sun Jan 30, 2005 9:04 pm ]
Post subject: 

Any sprockets for 87-88 T3 engine ???? I would be interested . Its going to machine shop tomorrow , done in few days need to put it back together . Might as well have a cam gear on it if its available . 8)

Author:  suprf1y [ Sun Jan 30, 2005 9:18 pm ]
Post subject: 

DTM GTi wrote:
Any sprockets for 87-88 T3 engine ???? I would be interested . Its going to machine shop tomorrow , done in few days need to put it back together . Might as well have a cam gear on it if its available . 8)


Its not really neccesary on the Mk1 cars unless you are running lots of cam. In that case, I would go max +6

Author:  GI-JOE [ Tue Feb 01, 2005 7:45 pm ]
Post subject: 

Check PM 8)

Author:  Shadychevyowner [ Wed Apr 20, 2005 9:04 am ]
Post subject:  96

Got any for a 96 3cyl.

Author:  suprf1y [ Wed Apr 20, 2005 5:47 pm ]
Post subject:  Re: 96

Shadychevyowner wrote:
Got any for a 96 3cyl.


I do now.
PM me if you are interested.

Author:  marmar [ Sun Jul 03, 2005 9:16 pm ]
Post subject: 

how bout a 97 sohc 4 banger?

Author:  Zurech [ Mon Jul 04, 2005 12:30 am ]
Post subject: 

If you dont have one of these, get one for your Swift :!:

Author:  suprf1y [ Mon Jul 04, 2005 7:21 am ]
Post subject: 

marmar wrote:
how bout a 97 sohc 4 banger?


Let me do some degreeing, and see if you really need one first. Good timing, I have one of those heads on my test bench right now.

Author:  Crvett69 [ Mon Aug 08, 2005 3:45 pm ]
Post subject: 

have you found out how the DOHC advance sprokets work and what would you recomend for a stock DOHC engine, 6 8 or 10% advance?

Author:  tuffcarguy [ Mon Aug 08, 2005 5:04 pm ]
Post subject: 

Crvett69 wrote:
have you found out how the DOHC advance sprokets work and what would you recomend for a stock DOHC engine, 6 8 or 10% advance?


http://www.teamswift.net/viewtopic.php?t=15919

mine responded very well to them 8)

Author:  Titanium50 [ Thu Sep 08, 2005 1:24 am ]
Post subject: 

Perhaps this is a silly question, but couldn't you get 9° (360°/40 teeth) of advance with stock cam pulley by advancing it 1 tooth?

Author:  n1tr0 [ Thu Sep 08, 2005 2:42 am ]
Post subject: 

Titanium50 wrote:
Perhaps this is a silly question, but couldn't you get 9° (360°/40 teeth) of advance with stock cam pulley by advancing it 1 tooth?

that's actually works out to be 18 degrees, you need to measure by the crank, not the pulley ... (or vice versa)
been there, tried that ..

Author:  Jerry Headley [ Fri Sep 09, 2005 6:47 am ]
Post subject:  '97 1.0 advance timing gear needed

:D Hi, I would like to purchase an advanced timing gear for a stock '97 Metro 1.0 3 cyl. Do you have one available? and what degree would you recommend for this 5speed car?
Thanks,
Jerry Headley
Union, Wa. USA

Author:  suprf1y [ Fri Sep 09, 2005 5:32 pm ]
Post subject:  Re: '97 1.0 advance timing gear needed

Jerry Headley wrote:
:D Hi, I would like to purchase an advanced timing gear for a stock '97 Metro 1.0 3 cyl. Do you have one available? and what degree would you recommend for this 5speed car?
Thanks,
Jerry Headley
Union, Wa. USA

I have one.
$25 + $8.50 shipping in US/Canada(those ones are heavy)
I recomend the +10 for your car.

Page 1 of 3 All times are UTC - 5 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/